TL;DR Position size is a calculation, not a feeling. You take your planned dollar risk, R, and divide it by the distance between your entry and your stop. That is the maximum share count. A tighter stop produces a larger share count; a wider stop produces a smaller one. Buying power, a round lot, or a ‘cheap’ stock are not the starting point.
Size comes from the stop
If risk management is the decision to lose a fixed amount, position sizing is the arithmetic that makes that decision true.
Rip’s version, written out in Position Sizing with R, is:
Shares = R ÷ stop distance
R is the planned dollar loss. Stop distance is the difference, in dollars per share, between the intended entry and the price where the idea is invalid. For a long, that is entry minus the stop. For a short, it is the stop minus the entry.
Example, for illustration only, not a trade: if R is $100 and you plan to buy at $50.00 with the idea invalid under $49.50, the distance is $0.50 and the cap is 200 shares. If the same idea is invalid under $49.00, the distance is $1.00 and the cap is 100 shares. The wider stop does not get “more room” for free. It gets fewer shares.
If the result is a tiny share count, the setup may not fit the account. The correct response is to skip it, not to ignore the stop or to inflate R for the afternoon.
Tight stops are not free size
A tight stop produces a larger share count, and that is mathematically consistent with a fixed R. It is only practical if the stop is a real invalidation, not a line squeezed close to the entry so that you can buy more.
If the stop sits inside the normal noise of the name — inside the spread, or well inside a typical ATR range — you are likely to be stopped out without the idea ever being tested, and the large share count will make those scratches expensive in friction.
Use a stop that belongs to the structure: a level, a cloud, a swing. Then accept the share count that falls out. If ATR says the name usually moves more than your entire distance in a few minutes, either widen the plan (and reduce shares) or pick a calmer name.
Round lots (multiples of 100) are a habit from an older market, not a requirement. Odd lots are fine. Do not increase the size to a round number if that takes you over R.
Friction, gaps and options
The formula uses the chart distance. The real loss can be larger.
- Spread and slippage can fill a stop beyond the trigger, especially in thin names and around the open.
- Overnight gaps can do the same on a swing.
- Fees are usually small now, but they still exist and should be in the journal.
If those effects are material, reduce the share count so that a bad fill is still close to one R, or do not use that name in that style.
Options need a different calculation. A long option can expire worthless, so the typical risk is the premium paid, plus fees, if that is truly the most you can lose. Short options can lose more than the premium. Convert the contract risk into dollars, then apply the same idea: the position should be limited to about one R if the planned invalidation happens. Do not translate “100-share equivalent” from a stock formula and assume it is the same risk. Start with Ripster’s options trading rules before you size a contract.
Practice the arithmetic until it is boring
Before the next five practice trades, written or live at small size, write down: entry, stop, R, share count. After the exit, write the actual fill and the actual dollar result in R. That is the drill in Start Here and in the journal lesson.
Buying power is not a target to use up. A “cheap” stock is not automatically a larger position. The cloud tells you the side and often the risk line. The formula tells you how many shares that risk line allows. When those two agree, you have a size. When they do not, you have a pass.
Common questions
What is the basic formula?
Shares = R ÷ (entry price − stop price) for a long, using the absolute distance for a short. Convert everything to dollars per share. Then reduce the count if the spread, fees or a possible gap make the true risk larger than the chart distance.
Why does a wider stop mean fewer shares?
Because R is fixed. If you are willing to lose $100, and the stop is $2 away, 50 shares is the cap. If the stop is $0.50 away, 200 shares is the cap, provided the name is actually liquid enough to exit there.
How does this work with options?
The idea is the same — define the dollar loss first — but the risk of a contract is not the same as the distance to a stock stop. Use Rip’s options rules lesson and size from the real dollar risk of the contract, not from the share-equivalent of the underlying.
Ripster lessons on this topic
Once the idea is clear, these are the matching lessons from Rip's method.
- Position Sizing with R: Shares or Contracts
- Risk Reward and the R System
- ATR and Relative Volume: How Far Can It Move?
- Ripster's Options Trading Rules
When you want to go further
Learn the method live with our team: voice and screen share, the morning game plan and a webinar library.
Visit Tenet Trade Group ↗ TENET RESEARCHResearch for swing traders and investors: curated lists, stock pages with Ripster EMA Clouds, and model portfolios.
See Tenet Research ↗Education only. Members learn to execute for themselves.
Sources: Ripster Education Position Sizing with R and Risk Reward lessons.
Education only, not financial advice. Trading involves risk, including loss of principal. This is not a recommendation to buy or sell any security. Confirm current account rules with your broker.
